The F-633 R control mount replacement magically appeared on the front steps today. I promptly went downstairs, drilled and trimmed the part per the plans. Using my drill press this time around yielded a perfect result. I mounted both brackets and test fit the control arms. It all worked perfectly.
Tomorrow I will be drilling and riveting all the nutplates and …
Tasks Completed:
The right side control mount didn’t turn out to my liking. It didn’t sit flat with the bulkhead because the holes are slightly off 90 degrees. I ordered a new part and moved on to riveting the forward bulkhead and arms together. A couple of rivets look suspect. I’ll drill out and redo tomorrow.
Also I spent time with the plans trying to figure out whether to countersink the bulkhead for the web stiffener riveting or dimple it. The bulkhead is .040. Technically for an AD4 rivet the material should be .050 thick. But if I dimple the material I am afraid I will enlarge the hole on the .063 web stiffener angle. Time to write Van’s.
Tasks Completed:
Tasks Completed:
Note: There is a badly seated pop rivet on the most outboard leading edge section. I’ll need to go back and repair later.
Tasks Completed:
Note: The trim tab has a slight upward curve caused by the misalignment of the top holes. I am not sure how the fit ended up being off slightly. This will be another item to ask the tech counselor about. Worst case, I’ll end up building Trim tab #3! I’ll save it for a rainy day in 2009!
Tasks Completed:
Note: A couple of the rivets for the horn did not seem to seat well. I will need to review with the tech counselor. Also getting everything dimpled and riveted together in the trim is a BITCH! I made a couple of cosmetic booboos to the skin trying to get dimple dies and a squeezer in there.
Okay–so after reading about putting this part together and an aborted attempt last night, I finally got around to bending the trim tab tabs for real.
First, I made another oak break with the interlocking notch at the top. I highly recommend oak or another hard wood because you are going put a lot of pressure on this break and you’ll want to minimize the flex.
The bends on each side worked very well this time. My only complaint is that I ended up with kinks on each trailing edge. This was caused by the trailing edge of the positive break was a tad thinner than the radius of the trim tab. So when all that pressure was applied the edge of the wood break put a kink in the trailing edge of the trim tab.
Tasks Completed:
I started on the trim tab tonight, but quickly got into a little trouble. The wood break I made for bending the elevator skin tabs does not have interlocking top half. So when I tightened the C-clamps the inside half slipped out causing a slight kink in the trib tab skin. It’s minor and helps “customize” my -7 but after that I hung up my tools for the night.
Tasks Competed:
Tasks Completed:
A lot got done today on the left elevator. I went over to a friends shop to get a good cut on the oak I planned to use on the sking tabs and trim tabs. I marched through the riveting of the skeleton and even the tab bending went quicker than I tought it might. Even with the doublestick tape I had trouble keeping the very end of the wood inplace for the bend. Overall I am pleased with the results. I hope to improve my tab bending art when doing the trim tabs.
When riveting the skeleton I waited to rivet E713 and 714 together. Instead, I first riveted the inboard rib to the spar and then riveted the outboard rib to both of these. Getting to the rivets that mount the ribs to the spar is WAY easier with this method. I also replaced the original counterweight with a new one because I had cut the original down. Getting the holes to line up with the counterbalance skin holes and the ribs holes was a pain. I highly recommend not screwing this part up in the first place. With a little body english, I finally got the bolts to fit.
Tasks Completed:
Today I was going to prime the left side parts but decided to go ahead and complete the riveting on the right elevator. Everything worked out well. When I do the left side I will be waiting to rivet 704 and 703 together until I get the short rib to the spar thereby avoiding the squeezer gymnastics needed to get all the rivets squeezed in that joint.
There’s two items I need to investigate further. First, Van’s came out with the soft rivet bulletin this weekend. Although I am not affected by their apparent mishap, it got me thinking that I had bought some rivets locally early on before knowing the difference between soft and hard rivets. And, just tonight, it felt like a few of the rivets were VERY easy to squeeze. The other thing I need to check on is the quality of my trailing edge bend. It seems like it needs a little more massaging in the middle sections to reduce some bowing I see. Work is going to kill me over the next couple of weeks so I might not get a lot more done on the elevators in November.
Tasks Completed: